0 items0.00

No products in the cart.

Category: Component

Component

Showing 100–108 of 162 results

  • 10D511K VDR Varistor 80V to 320V 10D511K VDR Varistor 80V to 320V MOV 10D511K VDR Varistor Epoxy Coated MOV For DOB MCPCB LED Bulb | Lights protection | DIY Science Projects | Circuits Safety Protection

    Read more
  • Features/Specs:
    Product: NTC Thermistor
    Thermistor number: 15D-15
    Resistance value: 15 Ω (ohm)
    Tolerance: ±1%
    Disk size: 15mm
    Number of pins: 2
    Mounting type: through hole
    Thermistor temperature range: -55℃ to +200℃
    Mounting Type: Through Hole
    Lead Spacing: 7.5 mm

    Read more
  • NTC Power Thermistor 5D-9 5 Ohm Thermistor 5D-9 R25: 5Ω; MAX.steady State Current: 3A ; Residual Resistance:0.21Ω ; Dissipation factor: 11 MW/℃ ;Thermal time constant: 34S Small size,large power,strong capacity suppression of inrush current;Fast response;Big material constant(B value),small resistance;Long life and high reliability;Complete series,wide applications Tolerance: ±20% Rohs

    Read more
  • 25N120 – 25A 1200V IGBT Transistor The KGT 25N120N from KEC is a 1200V, 25A IGBT in through hole TO-3P package. KEC NPT IGBTs offer low switching losses, high energy efficiency and high avalanche ruggedness for soft switching application such as IH (induction heating), microwave oven, etc.

    Read more
  • K30H603 TO-247 IKW30N60 IGBT Transistor 600V 30A 187W

    Read more
  • 50JR22 IGBT, DIP, Tube IGBT Transistors IGBT for Soft Switching AppsAnuj Enterprises are a Sole Proprietorship based firm, engaged as the foremost Wholesaler, Trader and Supplier of Laptop Charger, Matrix Display, LED Chip, etc.

    Read more
  • COMPONENTS 5v DC Power Relay SPDT 5 Pin Relays can be used to control both AC and DC appliance which comply with the output rating mentioned below. Relays are used in all cases when you need to control high current AC / DC using sensor outputs or microcontroller outputs subject to the need of relay driver circuits(in some cases). SPDT(Single Pole Double Throw) relay is used as a switch for high current AC/DC appliances which need to be controlled from a microcontroller or sensor output. 5V PCB Mount Sugar Cube SPDT Relay instead of its small size can switch a load of 7A connected to it. The coil resistance of this relay is 70 ohm whereas the coil current is 70mA. The trigger voltage for this relay is 5V. There are 5 pins in this relay i.e, Coil end 1, Coil end 2, COM(common), NC and NO. Coil end 1 and Coil end 2 are used to trigger ON/OFF the relay. One end is connected to a 5V supply and the other is connected to the ground of the circuit. Common is connected to the one end of the load to be controlled. The other end of the load is connected to either NC or NO. If the load is connected to NC(Normally Closed) then the load remains ON before trigger. And if it is connected to NO(Normally Open) then the load remains OFF before trigger. These relays are usually used in home automation, switching circuits, security circuits, etc. Trigger Voltage: 5V DC Max AC load current: 7A Max DC load current: 10A No. of Pin: 5

    Read more
  • LM7815 15V Linear Voltage Regulator 2A IC 7815 Output Voltage: 15V Output Current: 2A Thermal Overload Protection Short Circuit Protection Output Transition SOA Protection

    Read more